Notifications
Clear all
Forum Profile
Micha_AC
Micha_AC
Group: Registered
Joined: 2020-03-18
Eminent Member
2
Danke für den Tip mit dem Mehl. Ich hatte grade nach Kreides...

In forum [International] German

5 months ago
How to export colors?

In forum [Software] Third party

6 months ago
Niemand ne Idee?

In forum [International] German

10 months ago
Da gehts weiter:

In forum [International] German

10 months ago
Ja, wenn man das Calibrationsheet so hindreht, dass der Scan...

In forum [International] German

10 months ago
RE: Fabscan Fehlersuche

In forum [International] German

10 months ago
Fabscan Fehlersuche

In forum [International] German

10 months ago
Ach nice, der Teller dreht sich wieder :)Allerdings läuft je...

In forum [International] German

10 months ago
Vref hab ich einfach mal stumpf hochgedreht. Hat leider kein...

In forum [International] German

10 months ago
Stepper-Treiber

In forum [International] German

10 months ago
Painting black inside my fabscan

In forum [Hardware] Mechanics

1 year ago
Raspberry Pi HQ Camera supported?

In forum [Hardware] Electronics

1 year ago
As on every open source project ;)Any opinion on my camera s...

In forum [Hardware] Electronics

1 year ago
That's what it looks like. But as you can see in the video, ...

In forum [Hardware] Electronics

1 year ago
Just wanted to upload the logfile - but this odd forum doesn...

In forum [Hardware] Electronics

1 year ago
About the new UI I've read last year when I was testing. Any...

In forum [Hardware] Electronics

1 year ago
@marioThat's exactly what I added on github:

In forum [Hardware] Mechanics

1 year ago
@etofi Yes, it is, I soldered the switch before I could mana...

In forum [Hardware] Mechanics

1 year ago
Figured out my PSU was 12V 1.5A only - so I changed it and n...

In forum [Hardware] Electronics

1 year ago
okay, it's just a simple sudo python ./install

In forum [Hardware] Mechanics

1 year ago
I asume it's no shell script :DSo how do I start the install...

In forum [Hardware] Mechanics

1 year ago
Notifications disappear if calibration fails :(

In forum [Software] FabScanPi Server

1 year ago
@etofi thanks ;)

In forum [Hardware] Mechanics

1 year ago
@etofi which GPIO did you use? The schematics is not clear w...

In forum [Hardware] Mechanics

1 year ago
Shutdown-switch - which GPIO is free?

In forum [Hardware] Electronics

1 year ago
Nope. As my fabscan wans't running properly, I didn't spend ...

In forum [Hardware] Mechanics

1 year ago
When I bought the kit (it wasn't the full kit, as I had many...

In forum [Hardware] Electronics

1 year ago
And btw. is it timo to connect the laser's motors? until now...

In forum [Hardware] Electronics

1 year ago
Fabscan still instable - changing voltage regulator, adding ...

In forum [Hardware] Electronics

1 year ago
Just upgraded my heatsink and downloaded the image again (20...

In forum [Software] Operating System - Raspbian (SD-Card)

1 year ago
That's exactly why Im writing: theres no config file.

In forum [Software] Operating System - Raspbian (SD-Card)

2 years ago
Where to find config file?

In forum [Software] Operating System - Raspbian (SD-Card)

2 years ago
Well, finally I know what caused my problem. Tried to conn...

In forum Software

2 years ago
Power-LED and shutdown-button

In forum [Hardware] Mechanics

2 years ago
Same here. Got 2020-06-29 installed. Looks like calibration ...

In forum [Software] FabScanPi Server

2 years ago
Just got the new image (2020-06-29). But I couldn't get wifi...

In forum Software

2 years ago
Share: