Last seen: Apr 22, 2023
Yeay...der Fehler mit dem verdrehten Modell ist nach wie vor vorhanden...einmal Fabscan neugestartet, weil sich da mal wieder was aufgehangen hat, und...
Vor zwei Jahren hatte ich das Ding ja bei Watterott, die den Schrittmotor und ich meine auch die Laser gegen die originalen Komponenten aus dem Projek...
Ich hab den Fabscan heute nach knapp 2 Jahren Pause nochmal angeschmissen. Ich bekomm das Ding nach wie vor nicht dazu, zwei Scans hintereinander fe...
Fired up my Fabscan Pi again, after two years of sleep.Looks like server v0.10.2 is out now and current firmwareversion is dated 20200624. Is there a ...
Danke für den Tip mit dem Mehl. Ich hatte grade nach Kreidespray gesucht und bin darauf gestoßen, da ich mit zwei Testobjekten ebenfalls Probleme beim...
Niemand ne Idee?
Da gehts weiter:
Ja, wenn man das Calibrationsheet so hindreht, dass der Scanner es nicht zuerst umdreht und dann 58 Minuten und nach ner halbe Stunde später knapp 80 ...
Ach nice, der Teller dreht sich wieder :)Allerdings läuft jetzt erstmal 58 Minuten die Kalibrierung.Mal schauen, ob ich mir dann ne neue Kamera für de...
Vref hab ich einfach mal stumpf hochgedreht. Hat leider keine Änderung gebracht.Ich hab neulich noch TMC2130 in nem anderen Projekt verbaut und da war...
As on every open source project ;)Any opinion on my camera setup? Can you see what's faulty? Or any idea why I got so many errors in the log file?Or i...
That's what it looks like. But as you can see in the video, sometimes the image looks a little bit blue colored...
Just wanted to upload the logfile - but this odd forum doesn't allow the filetype log -.- Renaming it to txt helps...
About the new UI I've read last year when I was testing. Any progress on this? Are you already in alpha state? Isn't it the right camera? What do...
@marioThat's exactly what I added on github:
@etofi Yes, it is, I soldered the switch before I could manage to get the script working.I'm more the hardware guy....as sonn as I knew which GPIO to ...
Figured out my PSU was 12V 1.5A only - so I changed it and now I'm using 12V 4A - looks like the fabscan is working more stable now.Still didn't repla...
okay, it's just a simple sudo python ./install
I asume it's no shell script :DSo how do I start the installer? I assume it's a python script...
@etofi thanks ;)
@etofi which GPIO did you use? The schematics is not clear which one is free :(
Nope. As my fabscan wans't running properly, I didn't spend any time on it.At the moment I'll give it another attempt. If it works, I'll see what I ca...
When I bought the kit (it wasn't the full kit, as I had many party already here) it was common to mount the laser on the servo (which was included as ...
And btw. is it timo to connect the laser's motors? until now I had them disconnected, as the firmware didn't support it's movement :D
Just upgraded my heatsink and downloaded the image again (2020-10-13-FabScanPi-lite).Now the config-file works as exspected. No idea what changed.
That's exactly why Im writing: theres no config file.
Well, finally I know what caused my problem. Tried to connect to the 5Ghz wifi....but good old RPi3 only supports 2.4Ghz. Will a SSID-scanner and wi...
Same here. Got 2020-06-29 installed. Looks like calibration works fine. But when I would like to start a test-scan I get the message calibration faile...
Just got the new image (2020-06-29). But I couldn't get wifi up and running. Every time I reboot, the /boot/wpa_supplicant.conf file has gone....no ...
