This user account status is Approved

Forum Replies Created

RE: Just some impressions of the current testing version.

Hi, can I download and build the develop branch image by following these instructions ? Or do I also need to build Backend and Firmaware ? I have PyCharm community edition, will that work ? Are you us...

In forum [General] Hall of fame, show your Scans

3 years ago
RE: Just some impressions of the current testing version.

Hi, can I download and build the develop branch image by following these instructions ? Are you using 2 lasers ? I'm having some trouble focusing the laser line, seems to only work if the main body si...

In forum [General] Hall of fame, show your Scans

3 years ago
RE: Stepper motor mounting plate

@mario Danke schön !

In forum [Hardware] Mechanics

3 years ago
RE: Stepper motor mounting plate

Nennt man sowas "Flanschkupplung" ? Welle ist 5mm, Lochabstand 9mm, für jeden Tipp dankbar.

In forum [Hardware] Mechanics

3 years ago
Stepper motor mounting plate

Sorry, this might seem obvious for some of you, but where can I find this mounting plate for the stepper... I tried to make one myself, but it's far from stable...

In forum [Hardware] Mechanics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

Hi, i just wanted to report back. I ended up buying a second fabscan Hat and I couldn't get it to work either. So I called watterott, mailed my pictures and described my attempts and they agreed to a...

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

Hmm... Option B: Connect 12V DC to the HAT (round connector) and 5V DC to the raspberry (micro USB connector). NOTE: Make sure you switch on the both power sources at the same time to avoid software ...

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

Okay, I replaced those 4.65kΩ Resistors with the 2.163 kΩ, tried to flash the bootloader again, same result. I guess I'm giving up for now, I think I tried everything I could find on this forum. Some ...

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

My 2.2k Ohm resisitors measured 2.16k Ohm, so i used 4.65k Ohm, I wasn't sure whether everything between 2.2k and 5.6k is fine.

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

3rd Attempt: pi@fabscanpi:~ $ cd RPi-UNO-HAT/software/ pi@fabscanpi:~/RPi-UNO-HAT/software $ sudo avrdude -c pi_isp -p m328p -e -U flash:w:bloader.hex:i -U lfuse:w:0xFF:m -U hfuse:w:0xD6:m -U efuse:w...

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

2nd Attempt: pi@fabscanpi:~ $ cd RPi-UNO-HAT/software/ pi@fabscanpi:~/RPi-UNO-HAT/software $ sudo avrdude -c pi_isp -p m328p -e -U flash:w:bloader.hex:i -U lfuse:w:0xFF:m -U hfuse:w:0xD6:m -U efuse:w...

In forum [Hardware] Electronics

3 years ago
RE: Hat Not Working, Forum not working, pulling my hair out

Next I tried to flash the bootloader (bloader.hex) 1st Attempt: pi@fabscanpi:~/RPi-UNO-HAT/software $ sudo avrdude -c pi_isp -p m328p -e -U flash:w:bloader.hex:i -U lfuse:w:0xFF:m -U hfuse:w:0xD6:m -U...

In forum [Hardware] Electronics

3 years ago
Hat Not Working, Forum not working, pulling my hair out

Hi, I'm having trouble getting the HAT working. trying: sudo avrdude-autoreset -p m328p -b 115200 -carduino -P/dev/ttyAMA0 results in: avrdude-original: Using autoreset DTR on GPIO Pin 7 avrdude: s...

In forum [Hardware] Electronics

3 years ago
RE: Test, I can't post, wordpress Potentiall unsafe operation

A potentially unsafe operation has been detected in your request to this site Your access to this service has been limited. (HTTP response code 403) If you think you have been blocked in error, contac...

In forum [Hardware] Electronics

3 years ago
Test, I can't post, wordpress Potentiall unsafe operation

^See topic

In forum [Hardware] Electronics

3 years ago