[Sticky] How to setup WiFi.  

Page 1 / 2
  RSS
mario
(@mario)
Member Admin

Create a file in the /boot folder of your SD-Card. You can use a card reader or a wired connection to your pi to do that. 

The file must be called wpa_supplicant.conf  and contain the following lines: 

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=DE
network={
ssid="<replace with your network ssid>"
psk="<replace with your password here>"
key_mgmt=WPA-PSK
}

Maybe change the country code to your country. e.g. EN for England.
Now reboot or boot your Raspberry Pi. It should connect to your WiFi network and you are done.

Have fun.
Mario

This topic was modified 7 months ago by mario
Quote
Posted : 19/03/2019 8:03 pm
AndreaCH liked
Danilo0702
(@danilo0702)
Trusted Member

last release - Lan-network  via ssh --> login -- sudo raspi-config --> Nr. 2

IMG 5495
This post was modified 7 months ago by Danilo0702
ReplyQuote
Posted : 20/03/2019 7:50 am
AndreaCH and mario liked
aego
 aego
(@aego)
Active Member

Hello guys, I need help.
I followed every script for the installation of the sketch, but I do not succeed when I type the IP address of the raspberry in my browser (Firefox). The IP address is correct because I access via VNCviewer and Putty. What I did was follow this script:
I installed FabScan PI Raspbian Image: 2019-02-21-FabScanPi-Lite

I created in boot/folder the file wpa_supplicant. conf

Ctrl_interface = DIR =/var/run/wpa_supplicant GROUP = Netdev
Update_config = 1
Country = BR
Network = {
SSID = "Angelo 2.4 "
PSK = "Nicolau22 "
KEY_MGMT = WPA-PSK
}
But the browser cannot access the IP address. Time out

Any suggestions?

TIA

ReplyQuote
Posted : 04/06/2019 7:26 pm
mario
(@mario)
Member Admin

Hi, 

yes. Are you able to connect to your FabScan when it is connected by wire? Anyway, start your FabScan and go to http://find.fabscan.org  . If it will find a FabScan in your local network you will be automatically redirected to the device. If there are more than one FabScan in the network, you will end up with a list of ip addresses. 

- Mario 

ReplyQuote
Posted : 04/06/2019 10:35 pm
aego
 aego
(@aego)
Active Member

OK Mario. I will check tonight when I get home. I'm eager to make the fabscan work.
And thank you

ReplyQuote
Posted : 05/06/2019 9:29 pm
aego
 aego
(@aego)
Active Member

Hi Mario, it took me because I had to buy a network cable
Could not connect via cable directly to the router. The same errors that occur on the WiFi,  appear.
Via Link http://find.fabscan.org->
0 devices found
And through the link http://find.fabscan.or g" target="_blank" rel="noopener"> http://find.fabscan.org
No devices found in your network.

But Rasp is in the network and I access via VNC and via Putty.
This is driving me crazy.
Any more help?
Thank you and thank you

ReplyQuote
Posted : 06/06/2019 11:29 pm
aego
 aego
(@aego)
Active Member

Sorry here the correct msg

Hi Mario, it took me because I had to buy a network cable
Could not connect via cable directly to the router. The same errors that occur on the WiFi,  appear.
Via Link http://find.fabscan.org->
0 devices found
 
No devices found in your network.

But Rasp is in the network and I access via VNC and via Putty.
This is driving me crazy.
Any more help?
Thank you and thank you

ReplyQuote
Posted : 06/06/2019 11:32 pm
aego
 aego
(@aego)
Active Member

Ah, I also tried through the Cromium the http://localhost:8080 and http://128.0.0.1:8080. Time out and I couldn't access it.

ReplyQuote
Posted : 07/06/2019 12:55 am
aego
 aego
(@aego)
Active Member

Rasp IP 192.168.0.38

Microsoft Windows [versão 10.0.17134.765]
(c) 2018 Microsoft Corporation. Todos os direitos reservados.

C:\Users\Angelo>ping 192.168.0.38

Disparando 192.168.0.38 com 32 bytes de dados:
Resposta de 192.168.0.38: bytes=32 tempo=49ms TTL=64
Resposta de 192.168.0.38: bytes=32 tempo=5ms TTL=64
Resposta de 192.168.0.38: bytes=32 tempo=6ms TTL=64
Resposta de 192.168.0.38: bytes=32 tempo=8ms TTL=64

Estatísticas do Ping para 192.168.0.38:
Pacotes: Enviados = 4, Recebidos = 4, Perdidos = 0 (0% de
perda),
Aproximar um número redondo de vezes em milissegundos:
Mínimo = 5ms, Máximo = 49ms, Média = 17ms

C:\Users\Angelo>

This post was modified 5 months ago by aego
ReplyQuote
Posted : 07/06/2019 1:25 am
mario
(@mario)
Member Admin

Which version of FabScanPi Server do you have installed? 0.70 or earlier?

ReplyQuote
Posted : 10/06/2019 3:27 pm
aego
 aego
(@aego)
Active Member

2019-02-21-FabScanPi-lite

ReplyQuote
Posted : 10/06/2019 5:49 pm
aego
 aego
(@aego)
Active Member

one more thing, I am using RPI -Fabscan-HAT from Wattererot

ReplyQuote
Posted : 10/06/2019 7:29 pm
aego
 aego
(@aego)
Active Member

Hello Mario, I need your help.

What am I missing to make?

What did I do wrong?

Thank You

ReplyQuote
Posted : 11/06/2019 10:30 pm
aego
 aego
(@aego)
Active Member

After 6 days...

Well, I have to give up. No support I'm not going to make any progress. It makes me sad because I bet much on Fabscan.

ReplyQuote
Posted : 16/06/2019 5:42 pm
mario
(@mario)
Member Admin

Sorry, I am not able to reproduce the error. How are you able to use VNCviewer? Have you installed the package on the raspberry? Have you tried to connect on port 80, which is the default port when you connect to the IP address without giving a port in the url.

The fabscanpi lite images used haproxy to route all the incoming traffic on port 80 (http)  and 443 (https) to the server port 8080. 

If you are able to ping the fabscanpi on your given address, then it should be possible to connect to the interface by 

http://<address_of_your_fabscan>

of 

https://<address_of_your_fabscan> ( you need to confirm that the certificate is self signed)

(No need to add a specific port)

As an alternative way you can connect via: 

http://fabscanpi.local

This works on apple computers out of the box. On Windows you will need to install a zero conf driver  like apples Bonjour printer driver . This driver is also delivered with iTunes. 

 

If you are getting a timeout the proxy server must be down. Otherwise you will see the interface. If the fabscanpi server is not running, the proxy will show you a kind of diagnostic page with hints, what you can do.

This post was modified 4 months ago 4 times by mario
ReplyQuote
Posted : 16/06/2019 9:57 pm
Page 1 / 2
Share: