Forum Replies Created
RE: "Turm" über eigentlichem Objekt Thank you. With your hints and especially with the screenshots it worked now.The image is very dark because of the reduced brightness, especially when scanning with color. But the strange tower is gon... |
In forum [International] German |
3 years ago |
"Turm" über eigentlichem Objekt Nach etwas längerer Zeit habe ich mich wieder mit dem FabScan beschäftigt. Ich habe das gleiche Problem, das ich auch damals schon hatte. Mein Objekt wird gescannt, aber oben drüber entsteht ein unreg... |
In forum [International] German |
3 years ago |
RE: Komisches Scanergebnis @danilo0702 Einen Lüfter habe ich sowieso verbaut, da ich einen Pi4 verwende. |
In forum [International] German |
4 years ago |
RE: Komisches Scanergebnis @danilo0702 mit welchen Einstellungen hast du das gescannt? |
In forum [International] German |
4 years ago |
RE: Komisches Scanergebnis @danilo0702 und wie entfernst Du diesen „Schirm“? |
In forum [International] German |
4 years ago |
RE: Komisches Scanergebnis eventuell liegt es am Licht, das in die Kammer eindringt? Ist Dein Gehäuse dicht? Meins ist ziemlich stark verzogen und hat vorne an der Klappe einen richtig grossen Spalt. Watterott hat mir Ersatz ve... |
In forum [International] German |
4 years ago |
RE: Komisches Scanergebnis Es war tatsächlich so, dass eine der beiden Brücken nur so getan hat, als ob sie gebrückt wäre. Nun schaut das Ergebnis deutlich besser aus. Nun würde mich interessieren, warum in der Mitte dieser "Tu... |
In forum [International] German |
4 years ago |
RE: Komisches Scanergebnis @mario ich habe einen Motor mit 200 steps, tmc2208, C1 und C2 gebrückt, in der config 3200 eingestellt. Vielleicht stimmt ja doch etwas mit den Brücken nicht? Hierzu war ich schon mit watterott in Kon... |
In forum [International] German |
4 years ago |
RE: Help wanted with 3D design of calibration tool. I discovered something in a video here that could perhaps be reproduced in this way. Can that work?If that were promising, I could try to build something like that in fusion. |
In forum [Hardware] Mechanics |
4 years ago |
RE: Komisches Scanergebnis @mario Ich habe inzwischen Jen nochmal von vorne alles neu installiert. Leider hat der Scan immer noch keine Ähnlichkeit mit dem Original. Siehe Bilder. Woran könnte das liegen? Attachment : 5A559... |
In forum [International] German |
4 years ago |
Blue lines in preview Do the blue lines / dots affect the scan result?What causes it? Attachment : Anmerkung 2020-05-25 164914.jpg |
In forum [Software] FabScanPi Server |
4 years ago |
Komisches Scanergebnis Nachdem die Software nun läuft, konnte ich meinen ersten scan starten. Leider ist das Ergebnis sehr komisch und hat keinerlei Ähnlichkeit zum Original. Was läuft hier nich falsch? Attachment : D32... |
In forum [International] German |
4 years ago |
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts Nach update werden auch bei processes 4 die Punkte während des scans angezeigt. |
In forum [International] German |
4 years ago |
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts @mario folgende Meldung kommt: pi@fabscanpi:~ $ sudo apt-get update && apt-get dist-upgradeGet:2 buster InRelease [15.0 kB]Get:3 buster InRelease [25.1 kB]Get:1 stable InRelease [3,946 B]Ge... |
In forum [International] German |
4 years ago |
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts @mario ja, man sieht die Punkte während des scans. Ist mein erster Scan. Und der sieht im Ergebnis sehr komisch aus. Dafür mache ich aber ein eigenes Thema auf. |
In forum [International] German |
4 years ago |
RE: Fokussierbarer Laser danke, so habe ich mal einen Anhaltspunkt. |
In forum [International] German |
4 years ago |
Fokussierbarer Laser ich habe mir die fokussierbaren Laser für meinen FabscanPi bestellt. Jetzt bin ich etwas unsicher, wie schmal die Linie sein muss bzw. wie breit sie sein darf. Wie sind Eure Erfahrungen. Ich schätze m... |
In forum [International] German |
4 years ago |
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts Habe ich das richtig interpretiert, dass momentan kein Scannen möglich ist, bis es eine neue Software Version gibt? |
In forum [International] German |
4 years ago |
RE: New version of the housing? ok, some questions answer themselves if you have built a bit further.The horseshoe-shaped hole has the ingenious function that you can access the SD card from above. |
In forum [Hardware] Mechanics |
4 years ago |
New version of the housing? Today I got my housing from Watterott. Unfortunately, an angle from the lid is cut incorrectly. A notch is missing.I hope to get a replacement. There is a horseshoe-shaped hole in the base plate that ... |
In forum [Hardware] Mechanics |
4 years ago |
RE: FabscanPi with Pi4 @mario many thanks for the quick reply.I'll take the fan into account with the part of thingiverse.Is it possible to tap the required 12V directly from the Pi Hat? |
In forum [Hardware] Electronics |
4 years ago |
FabscanPi with Pi4 Hello guys I would like to build a FabscanPi and use the Pi4 straight away.The V7805-2000 cannot be used due to the higher power consumption. Can I use this one here?I am not the great electronics en... |
In forum [Hardware] Electronics |
4 years ago |