One more update, I an scanning w/o color.

Update - I was able to complete a scan at 100% resolution, but when I tried to download the file from the UI I received a 404 error. But, I was ab...

@mario  Well, Yes I was, but this was a low resolution scan, 52,000 Kb, down loaded and opened in meshlab. Was also able to do the same with a ...

All working great on my system. Thanks for the work Mario!

Sorry for English, I have been planning on doing this, great Idea and Thanks for sharing!!

@trife I was able to get one of my hats to work with the new software and the current boot loader. I was connected to the hat as per the above docu...

@hamishi Is your calibration sheet 10mm or is it 11mm?

@mario No Problem, It works great!! Keep up the good work!

@danilo0702 Thanks much - I knew the screen looked familiar. Have a good day.

@mario Well - a FTP client was my first guess and you confirmed it! Thanks much!!!

@daniloo702 Sorry for the English, maybe Mario can translate, if needed or knows the answer to my question below. I am still learning how to interface...

All, Never mind it is working now. The only think I can figure out is that I was trying too large of a scan. This is solved, sorry for the confusion.

Additional information; Here is the list of log files in the fabscanpi directory, just let me know which one you need. pi@fabscanpi:/var/log/fabscanpi...

@mario OK, I understand didn't know about the simple scan, that is good to know and have been using external meshlab. Which log file do you need? And,...

@hamishi OK, I didn't have that problem, I must be lucky, all I had to do was tweak the lens a little to the right and the green cross hairs aligned u...

Very Nice, Thanks for the photos! When you say Camera was way off - do you mean focus? If so were you able to adjust the camera lens with the focus t...

Posted by: @hamishi That is good news! I will test the driver tonight and I did find out I have a TMC2208. Can you send some photos of your enclosur...

@hamishi Very good information. Did you have a chance to test this yet?

@mario Ran the test and not what I expected!! G00 T12800 F10000 is required to make the motor turn 360 degrees. Not sure which Silentstick I have, th...

@hamishi Sounds like we might have the same problem, take a look at the post, it has more detail and I agree we don't know what else has changed. Soun...

@mario Interesting thought, there is nothing above the black object (where the purple cloud is located). The object is a Black 110VAC electrical plug...

@mario Thanks, I also found the same documentation.

@mario Well Mario, you are a miracle worker. That worked! The server and browser are up an running, time to work on calibration and a scan. Many Tha...

@mario Stopped the server, ran the next command and received the response we needed, modified the config file, restarted server and even rebooted. Her...

@mario Should we stop the server before executing the command listed below? sudo avrdude-autoreset -p m328p -b 115200 -carduino -P/dev/ttyAMA0Yes. The...

@mario Well tat would make sense. I figured you were on top of the situation. Please let me know if there is anything I can do to help. Thanks for yo...

@justinb I am having roughly the same issues that you have are having. However, I believe I was able to flash the boot loader OK. Just not sure how to...

@mario I have been researching this issue and have found some more information, which lead to more questions ? . In the documentation there is a refer...

@mario As per your request. The log file is quite short and is attached I also attached the output of ps -axf command. I am now in SSH mode via PuTT...

@mario OK, sounds good. What you say makes sense and was why I was asking about "raspi-config" and how to configure to boot selections. When I switch...

@mario OK, sounds good, attached are the files you ask for. Thanks again, we are getting somewhere!!

@mario Well I dis some further testing tonight and think I found out why the "sudo avrdude-autoreset -p m328p -b 115200 -carduino -P/dev/ttyAMA0" comm...

Sorry for English - Google will translate for you. Check here "Can not get Software running after reflashing pi HAT. " in the Hardware FAQ. I have the...

@mario Yes, I agree, 57600 seems to work, but not all the time, does the error "avrdude: stk500_recv(): programmer is not responding" concern you? Eve...

@mario I did as you suggested and the results puzzle me. I attached a file with the results. This log is the results after installing a new image in...

@gzusman Not much to add, except that, if I connect a HDMI monitor to the HAT, once the system boots the screen goes blank except for a blinking curso...

@Mario, Update - New hardware, Fresh SD card Image - Nothing changes. Browser displays famous message and Log ends with "Trying to connect Arduino on...

@Mario The software continues to hang "Trying to connect Arduino on port: /dev/ttyAMA0". Could this problem be related to administrative rights for th...

@hexa-quax and Mario, Additionally, I decided to purchase a new HAT and PI, thinking I might have some bad hardware. And wanting to have a fresh start...

@hexa-quax Good Day, What changes did you make to the "default.settings.json" - file. Thanks,

@mario Tried;pi@fabscanpi:~ $ sudo /etc/init.d/fabscanpi-server restartRestarting fabscanpi-server...avrdude-original: Using autoreset DTR on GPIO Pin...

@Mario, I continue to troubleshoot this issue. I checked the running services and found the following. pi@fabscanpi:/usr/bin $ sudo service --status-...

@Mario, I have tried 2 different SD cards with fresh installs and the results are the same. I agree that the log file is short, but that is all that i...

@ralf02 Resistors for loading the blonder.hex file, but I figured it out, thanks for the help.

@Mario, More info. I ran the “PS” command and everything looks as per the browser screen except the number after of the “root” is a lot smaller (~700...

@Mario, Update! Got the SSH to work using PuTTY. Below is the contents of the fabscanpi.log file from the "/var/log/fabscanpi/" location, not much th...

@Mario, OK stupid question - Sorry this is all new to me! I want to send you the log file, but I can't back to the command line so I can download it, ...

@Mario, I will send you a log file, is this the on you need "/var/log/fabscanpi/fabscanpi.log", or is there another one? Thanks again,

Understand - That file location gets me this file. Which is what I think we need, I will download it to the HAT and see what happens. :107E00001F92CDB...

Ok, I think I figured out how to add a file as a attachment.

@Mario Not sure how to attach a file, It is a big file, here you go. Hope this helps. Thanks again <!DOCTYPE html><html lang="en"><head...

@Mario, I will have to see how to do that. In the mean time I did some further testing and I want to make sure that the correct bloader.hex file is l...

@Mario, Thanks for the reply. That seemed to let me download and install the bootloader. The Pi continued to boot to the command line and reported th...

Hi @Mario I followed the instructions and used the new .hex file as per your post. When I try and flash toe boot loader I get the message below (highl...

Sorry for the english! @ralf02 - what resistor values did you use? German Translation via Google. @ralf02 - Welche Widerstandswerte haben Sie verwende...

Having the same problem and looks like I need to Flash the FabscanPI HAT bootloader. Have a couple of questions about flashing using Option A. Please...