mario
mario
@mario
Admin
Honorable Member
Joined: Oct 9, 2018
Last seen: Feb 27, 2024
Topics: 55 / Replies: 517
Reply
RE: WS2812B ring problem

Sorry for the late response, can you post some pictures of your board please? There are several versions/clones of the HE3D. Some pinouts are differen...

2 years ago
Reply
RE: Twin laser: Bad scans

@iadegesso is that the same object as on the first pictures?

2 years ago
Reply
RE: Twin laser: Bad scans

Still looks like bad calibration values to me. There is no need to do any jumper settings while using a TMC 2100. But i recommend to set the curren...

2 years ago
Reply
RE: Twin laser: Bad scans

Hi, have you tried to perform a scan with just one laser to be sure that the basic software setup is working. Does your motor run in 1/16 step mode...

2 years ago
Reply
RE: TMC2209 V1.2 von Bigtreetech vs. Silentstepstick TMC2209

Hi, sorry für die späte Antwort. Also generell sollte es kein Problem sein die Treiber auszutauschen. Es ist nur wichtig das die Konfiguration p...

2 years ago
Reply
RE: How to export colors?

Colors are already included in the PLY format. PLY is not a binary format you can view the raw data in a text editor. More information about PLY can b...

2 years ago
Reply
RE: Editing the config files permission denied.

Welcome @Zeltrax, if you are using the pi user for connecting to the Raspberry Pi, you need to use sudo in front of your editor command. All files ...

2 years ago
Reply
RE: Fabscan-Kalibrierung wird mit Fehler beendet

Der Fehler deutet darauf hin das irgendwas mit der Kamera Auflösung Problematisch ist. Mich wundert eigentlich dass der Fehler nicht durchgehend auftr...

2 years ago
Reply
RE: Fabscan-Kalibrierung wird mit Fehler beendet

@wolf2021 ist das ein Ciclop Aufbau? Also Scanner ohne Gehäuse oder ist es alles in einer Box? Für den Fall das es ein offener Aufbau ist sollte das I...

2 years ago
Reply
RE: Fabscan-Kalibrierung wird mit Fehler beendet

@Wolf2021 also ich hätte jetzt auch auf einen Fehler beim Pattern gesetzt. Ich konnte den Fehler in den Logs genau so reproduzieren (durch falsche Anz...

2 years ago
Reply
RE: Fabscan-Kalibrierung wird mit Fehler beendet

Hallo, ich hänge mich mal mit rein, muß aber gestehen dass ich die von euch zusammen getragenen Daten erst mal anschauen muß. Irgendwie bekommen...

2 years ago
Reply
RE: Calibration Fail server v0.10.0

This log shows only the startup sequence of your sever. The most interesting part is missing. I need the part when you started the calibration and the...

2 years ago
Reply
RE: Calibration Fail server v0.10.0

Hi, this is mostly affected by a bad config file. Can you proof your config and compare it to the default one: Especially have a look for mis...

2 years ago
Reply
RE: The FabScanPi server is currently not running (no logfile)

The logs are located in /var/log/fabscanpi Mostly the issue of non running daemon is caused by the serial connection which is not working. You shou...

2 years ago
Reply
RE: Stepper motor mounting plate

Ja genau. Es gibt aber auch bei Thingiverse Lösungen zum selber drucken.Das war zwar für den FabScan CUBE. Aber sollte beim FabScan Pi genau so gut pa...

2 years ago
Reply
RE: Probleme nach dem Update v.0.10.0

Welche Auflösungsstufe hast du gewählt zum Scannen ?

2 years ago
Reply
RE: Probleme nach dem Update v.0.10.0

Kannst du mal ein Bild vom dem Teil hochladen, was du scannen möchtest? Da kann ich dann besser einen möglichen Fehler analysieren.

2 years ago
Reply
RE: Stepper-Treiber

Da stimmt was nicht, ich tippe auf falsche Angaben von Zeilen und Spalten in der Konfiguration. Kalibrierung dauert i.d.R zwischen 6 bis 8 Minuten.

2 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

Dem Log kann ich jetzt erst mal keine Fehler entnehmen. Welchen Pi verwendest du? 4 oder 3. Der Raspberry Pi 4 benötigt ein ausreichend großes Netztei...

2 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

@keckei ich habe mir zunächst einmal das Board angesehen. Das mit den LED's wird nicht so einfach über den 6pin header funktionieren. Der ist komplett...

2 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

@keckei Der Link funktioniert zwar nicht, führt auf eine 404 Seite. Bei Aliexpress habe ich aber ein solches Board gefunden. Das ist nur eine Kombi au...

3 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

@keckei ja. Also im Prinzip wird die Firmware automatisch geschrieben. Das HAT ist auch nichts anderes als ein Arduino mit integriertem ZUM Shield, we...

3 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

Spannend. Könntest du mir Bilder davon zeigen, oder besser noch es mal zur Verfügung stellen. Ich denke es gibt bestimmt noch mehrere mit dem gleichen...

3 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

Muss es auch nicht zwingend notwendig sein. Kannst du mir Bilder davon schicken. Im Prinzip wird unter dem Board sicher auch nur ein Arduino Clone ste...

3 years ago
Reply
RE: Wo bekomme ich ein Fabscan HAT und Step Down

Was genau funktioniert nicht? Hast du dir die Anweisungen unter :genauer angeschaut? Die Hardware gibt es eigentlich bei Watterott, falls es dort ...

3 years ago
Reply
RE: New file Fabscan-Case for CNC

@Danilo0702 i think he means the dxf and svg files of your case design. The attached files are not downloadable.

3 years ago
Reply
RE: Calibration fails with "main.calibration_mode_not_defined"

@riegera2412 thank you, i will have a closer look to it, when i am back at home with hands on my hardware.

3 years ago
Reply
RE: Calibration fails with "main.calibration_mode_not_defined"

0.9.x comes with a memory leak which results in a crash of the software during high res scans.

3 years ago
Reply
RE: Calibration fails with "main.calibration_mode_not_defined"

I think something in the UI of v.0.10.0 is missing. I did some changes related to the calibration process. I will try to add a new testing version in ...

3 years ago
Reply
RE: Calibration fails with "main.calibration_mode_not_defined"

It is important that all hardware components (Laser(s), LED, Camera and Turntable ) are working. Check each component by using the hardware controls o...

3 years ago
Reply
RE: Calibration fails with "main.calibration_mode_not_defined"

@riegera2412 thank you for reporting this. It seems to be a bug. I am on vacation and will try to fix that when i am back at home.

3 years ago
Reply
RE: Maths / code that takes into account the rotary angle for each laser scan aquired

Hi and welccome, i'm on vacation at the moment and i don't have the best internet connection, i will try to answer your question when i am back at ...

3 years ago
Topic
Replies: 1
Views: 964
Reply
RE: Neueinsteiger: Gibt es die dxf-Daten für den Scannerkasten ?

Ich glaube da gibt es ganz frisch was. Schau mal hier vorbei:/p>

3 years ago
Reply
RE: Ich komm mit meinem Fabscan nicht weiter

Ein log Auszug wie oben beschrieben wäre nicht schlecht um etwas mehr Information zu erhalten was genau vor sich geht. Meist liegt es aber an der Seri...

3 years ago
Reply
RE: Probleme beim Scan. Ergebnis sieht vielfach gespiegelt aus

@saar96 das sieht jetzt aber nach einer echt schlechten Kalibrierung aus. Beide Punktwolken ( für jeden Laser eine) scheinen stark verschoben. Scha...

3 years ago
Reply
RE: Probleme beim Scan. Ergebnis sieht vielfach gespiegelt aus

@saar96 es ist super wichtig dass du den FabScanPi Server nach einer Änderung an der Konfiguration neu startest. Ansonsten werden die Änderungen nicht...

3 years ago
Reply
RE: Probleme beim Scan. Ergebnis sieht vielfach gespiegelt aus

Ja ich muss leider die Foren Einstellungen so restriktiv machen, da die SPAM bots immer besser werden.

3 years ago
Topic
3 years ago
Replies: 0
Views: 628
Reply
RE: Probleme beim Scan. Ergebnis sieht vielfach gespiegelt aus

Schau mal hier nach Dort steht wie du die jeweiligen Treiber konfigurieren musst.

3 years ago
Reply
RE: Stepper motor mounting plate

Maybe this will work too. It was designed for the FabScan CUBE ( in 2014).

3 years ago
Reply
RE: Scan kann nach Kalibrierung nicht gestartet werden

Hallo Dan, ich vermute du hast nur einen Laser und in der Konfiguration stehen unter numbers 2. Die Lösung wäre dann in der default.config.json di...

3 years ago
Reply
RE: Power-LED and shutdown-button

I will prove if i can include the script into the next image

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Danke für die Rückmeldung. Dann markiere ich das hier mal als gelöst. Wenn es mit dem neuen Pi ein Problem gibt melde dich.

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Du verwendest einen Raspberry Pi 3 B+ oder? Startest du es mit sudo? Also wie man noch tiefer reinschauen kann weiss ich nicht. Aber es scheint als gä...

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Danke noch mal für die Erläuterungen. Mit welcher Baudrate verbindest du dich? Und ist diese Baudrate auch in der FabScan Config eingetrage?

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Das ist alles sehr seltsam, vor allem weil beide Versionen nicht zu funktionieren scheinen. Bisher hat außer Dir noch keiner diesen Fehler so beschrie...

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Debug ist zur Zeit default, solange es zumindest noch kein Major Release 1.x.x gibt. Debug ist das höchste was zur Zeit geht. Da ist aber auch i.d.R. ...

3 years ago
Reply
RE: Aktuelles 0.9.4 Image funktioniert nicht - The FabScanPi server is currently not running

Hallo rsprecht, das ist echt seltsam. Normalerweise sollte auf jeden Fall ein Log geschrieben werden. Bist du bei der Installation der Version 0.9.4...

3 years ago
Reply
RE: Vorhandener 3d Scanner von 3Shape

Hallo Dennis, ich kenne das Gerät leider nicht. Scheint aber ein Kommerzielles Produkt zu sein, hast du mal auf der Seite des Herstellers nachgeseh...

3 years ago
Reply
RE: Software und Hardware Allgemein

Hallo Martin, willkommen in der FabScan Community. Ich war so frei und habe das Thema mal in den deutschen Bereich verschoben. Du schreibst 2 ...

3 years ago
Reply
RE: Range of the scanner?

It should be possible to build it bigger, with a custom turntable and/or case. The software is able to handle that. But there will be a limit, when th...

3 years ago
Reply
RE: Fabscan still instable - changing voltage regulator, adding second servo for second laser?

Nope. "It is done when it's done." Development depends on my spare time and my priority list. At least of course on volunteers working on the project....

3 years ago
Reply
RE: Fabscan still instable - changing voltage regulator, adding second servo for second laser?

@micha_ac it is not the biggest secret that the user interface is still not the best. And i can promise you that there will be no further work on this...

3 years ago
Reply
RE: Power-LED and shutdown-button

I never tested it. You should open an issue on GitHub and ask the project owner.

3 years ago
Reply
RE: Shutdown-switch - which GPIO is free?

Something similar was already done by a user: Only the Serial GPIO's of the Raspberry are used. Have a look at the schematics.

3 years ago
Reply
RE: Ply to stl convert

Keep in mind my book is only available in german. I am planing to release some of the major instructions on the blog in english soon. But if you are...

3 years ago
Reply
RE: First callibration freeze, network loss and scan fail

I guess you are using one Laser. Check your default.config.json file and set number of Lasers to 1 (default in the config is 2, since the latest relea...

3 years ago
Reply
RE: Odd scan!!!

If you purchased your HAT at Watterott electronics, then just contact them via E-Mail. And tell them that you already have purchased a couple of HATs...

3 years ago
Reply
RE: Freie bzw. unbelegte GPIO

Es kann sein das es auch wirklich noch länger als nur ein paar Wochen dauert, da ich zur Zeit der einzige Entwickler an der Software bin. Das ganze Fr...

3 years ago
Reply
RE: Odd scan!!!

Your video shows the behaviour. The scan is doubled. That means that one scan process turns the table two times. Check the motor you are using. Find o...

3 years ago
Reply
RE: FabScan kit build help

Yes the video is old and there is no new video until now. But there is a video made by Heinz Schmitz on YouTube (in german) Maybe this will help ...

3 years ago
Reply
RE: Freie bzw. unbelegte GPIO

Hi, willkommen in der community. Es gab bereits jemanden der das ziemlich gut umgesetzt hat. Schau mal hier Ich arbeite an einem komplett neue...

3 years ago
Reply
RE: Problem with scan

If you changed the default.config.json since your last calibration, it is always a good idea to do a new calibration.

3 years ago
Reply
RE: "Generate Mesh" Option

Ja. Ich muss zu meiner Schande gestehen, dass ich die Doku immer noch nicht zu 100% gerade gezogen habe. Es fehlt noch an allen Ecken und Enden an Det...

3 years ago
Reply
RE: Probleme mit Doppelbild / gespiegelter Scan

Der Post war nicht unbedingt unnötig, sofern andere Benutzer bei gleichen Problemen dadurch eine Lösung haben. @etofi danke jedenfalls für die Rückm...

3 years ago
Reply
RE: Probleme mit Doppelbild / gespiegelter Scan

Nicht unbedingt. Bist du sicher dass dein Motor 200 Schritte macht? Wenn das ein FabScan Kit ist und erst vor kurzem gekauft wurde dann sollte es ein ...

3 years ago
Reply
RE: Max Potential Objec Size

I think it is not possible with the default housing, cause the default sizes are 140 (table diameter) and max height of the object can be about 140 -1...

3 years ago
Reply
RE: Can't do a scan

Are you using one or two lasers? If you are using only a single laser, you need to adjust the number of lasers value form 2 to 1 in the config file. R...

3 years ago
Reply
RE: driver setup

Hi, that is correct. You need to bridge those pads. But the description of @leonnoel is for the TMC2208. The TMC2209 needs an additional bridge cfg...

3 years ago
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

@emw ich habe es endlich geschafft die nötige Zeit zu finden. Hier ist ein Bild. CFG1 und CFG2 müssen für Verwendung des TMC2208 von 5V auf die M...

3 years ago
Reply
RE: Where to find config file?

Hi, you should find it, like @Danielo0702 already mentioneed, in /etc/fabscanpi Anyway. Have a look at the GitHub Repo - Mario

3 years ago
Reply
3 years ago
Reply
RE: v 0.9.4.-Out Of Memory Exception beim scannen

Hallo, Das ist natürlich böse. Du könntest als workaround erst mal versuchen Swapping zu aktivieren. So dass zusätzlicher Speicher auf der SD-Kar...

3 years ago
Reply
RE: FabScan Review auf YouTube

Sorry, ich habe es noch nicht geschafft. Ich versuche es noch diese Woche zu testen dann schreibe ich dir hier die Lösung. Ja wir können gerne ein...

3 years ago
Topic
Replies: 7
Views: 798
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

@emw sorry hatte noch keine Zeit. Ich teste heute Abend noch mal fix mit den 2208 Treibern, dann kann ich es in der Doku aufnehmen. Das Problem tritt ...

3 years ago
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

@emw Das Objekt wurde zwei mal gescannt. Das liegt dran das die Anzahl der Steps in der Konfigurationsdatei nicht stimmt. Du hast 2 Möglichkeiten das ...

3 years ago
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

@emw kannst du mal ein paar Bilder von deinem Objekt teilen, das würde helfen bei der Fehlersuche. Die Dateien findest du in /home/pi/scans. Das Verze...

3 years ago
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

@emw ich vermute du hast einen Laser aber die Anzahl der Laser steht in deiner Konfiguration auf zwei. Schau dort einfach mal nach. Wenn das so ist, d...

3 years ago
Reply
RE: Problem importing into meshlab and meshmagic

0 as value for face is fine for a raw scan. face defines the number of triangles for a meshed scan. FabScan delivers only a pointcloud what means that...

3 years ago
Reply
RE: Can’t find server or server not starter

Please check if you bridged the safety switch connector, otherwise add a safety switch. See laser connection section in documentation:

3 years ago
Reply
RE: Can’t find server or server not starter

I need more information about the error. Please describe what kind of error. Which browser are you using? Which FabScan-Server version are you using, ...

3 years ago
Topic
Replies: 1
Views: 831
Reply
RE: Viele falsche Punkte über dem eigentlichen Objekt

Ich kann mich den Vorschlägen von @leonnoel nur anschließen. Dazu kommt noch dass es generell, immer wenn 3D Scanner mit Kameras und Licht arbeiten, u...

3 years ago
Reply
RE: Release v.0.9.3 is available.

So the preview is showing up for you with a plain installation from the latest sd-card image?

3 years ago
Reply
RE: Release v.0.9.3 is available.

@olivers i did some investigations on that issue. This seems to be a Firefox security feature issue. I don't know yet how to fix that. But i think i w...

3 years ago
Reply
RE: Release v.0.9.3 is available.

Can you attach the log file?

3 years ago
Reply
RE: Release v.0.9.3 is available.

@heinzschmitz könntest du mir noch das Log file anhängen? Es liegt in /var/log/fabscanpi/fabscabpi.log

3 years ago
Reply
RE: Scan scheint zu laufen, auf dem Bildschirm erscheint nichts

Ich habe meinen Scanner jetzt offline getestet und den Fehler reproduzieren können. Ich habe den Fehler auch behoben. Es läuft jetzt. Ich werde noch e...

3 years ago
Page 1 / 6